Welcome to our website
To take full advantage of all features you need to login or register. Registration is completely free and takes only a few seconds.
Summary
Product:
Linksys USB200M
Vendor:
Linksys
Tested operating systems:
Ark Linux, Debian GNU/Linux, Linux other, SLAX, Ubuntu Linux
Most recent version of this submission:
Linksys USB200M
Average Rating:




Submit a new result for this product
Operating System: Linux other Rating:





Submitted on 2005-01-01 12:00:00
Operating System: Ubuntu Linux Rating:


Submitted on 2006-12-13 10:04:48
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
I have a Linksys USB200M ver 2.1 and it will not work on Ubuntu. The device is recognized and handled by usbnet. A network interface is created, but no traffic is successfully transmitted. Previous versions of this device worked well with usbnet.
Operating System: Debian GNU/Linux Rating:


Submitted on 2007-04-06 11:13:16
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
This product is not properly working on my machine. I can see messages when it is plugged in. Device (eth) is created and the device can be pinged.
I cannot make it work to send data or ping outside of the box.
I cannot make it work to send data or ping outside of the box.
Operating System: Ark Linux Rating:





Submitted on 2008-03-26 19:40:10
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
works out of the box with 2.6.22, ethernet interface created immediately, no problem
Operating System: SLAX Rating:





Submitted on 2008-07-29 00:29:58
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
Works fully under Slax 5, not at all under Puppy 2, as they are both outdated comments on Puppy might not be true anymore. USB200M VER2
Operating System: Ubuntu Linux Rating:





Submitted on 2008-10-15 21:37:17
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
I'm using Ubuntu 8.04 kernel 2.6.24-18-generic.
Everything works by just pluging it in:
4151.076069 eth1: register 'asix' at usb-0000:00:1d.7-5, ASIX AX88772 USB 2.0 Ethernet, 00:1d:7e:01:37:44
4151.076112 usbcore: registered new interface driver asix
4151.283277 eth1: link down
4151.289148 ADDRCONF(NETDEV_UP): eth1: link is not ready
4156.540327 tg3: eth0: Link is down.
4160.739038 ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
4160.742292 eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
4168.385975 usb 4-5: USB disconnect, address 5
4168.386591 eth1: unregister 'asix' usb-0000:00:1d.7-5, ASIX AX88772 USB 2.0 Ethernet
Everything works by just pluging it in:
4151.076069 eth1: register 'asix' at usb-0000:00:1d.7-5, ASIX AX88772 USB 2.0 Ethernet, 00:1d:7e:01:37:44
4151.076112 usbcore: registered new interface driver asix
4151.283277 eth1: link down
4151.289148 ADDRCONF(NETDEV_UP): eth1: link is not ready
4156.540327 tg3: eth0: Link is down.
4160.739038 ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
4160.742292 eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
4168.385975 usb 4-5: USB disconnect, address 5
4168.386591 eth1: unregister 'asix' usb-0000:00:1d.7-5, ASIX AX88772 USB 2.0 Ethernet
Operating System: Debian GNU/Linux Rating:





Submitted on 2008-12-04 12:33:21
Anonymous
Post License:
GNU LGPL
Post License:
GNU LGPL
detected and set OK right away after plugin
then ifup got it an IP@ using DHCP
debian sarge 2.4.27 updated to etch and still running
then ifup got it an IP@ using DHCP
debian sarge 2.4.27 updated to etch and still running

Post License:
-